'----------------------------------------------------------------
'SHOPBOT ROUTER FILE IN MM
'GENERATED BY PARTWorks
'Minimum extent in X = 0.000 Minimum extent in Y = 0.000 Minimum extent in Z = -12.300
'Maximum extent in X = 500.000 Maximum extent in Y = 450.000 Maximum extent in Z = 0.000
'Length of material in X = 500.000
'Length of material in Y = 450.000
'Depth of material in Z = 12.300
'Home Position Information = Bottom Left Corner, Material Surface 
'Home X = 0.000000 Home Y = 0.000000 Home Z = 20.000000
'Rapid clearance gap or Safe Z = 5.000
'UNITS:MM
'
IF %(25)=0 THEN GOTO UNIT_ERROR	'check to see software is set to standard
SA                             	'Set program to absolute coordinate mode
CN, 90
'New Path
'Toolpath Name = Profile 1
'Tool Name   = 1/4" Up-cut (13729)

&PWSafeZ = 5.000
&PWZorigin = Material Surface
&PWMaterial = 12.300
'&ToolName = "1/4" Up-cut (13729)"
&Tool =4                    'Jog Z axis to safe height
C9
TR,14000
C6                   'Return tool to home in x and y
PAUSE 2
'
MS,75.9,25.3
JZ,20.000000
J2,0.000000,0.000000
J3,50.000000,50.000000,5.000000
M3,50.000000,50.000000,0.000000
M3,150.000000,50.000000,-3.075000
M3,50.000000,50.000000,-6.150000
M3,150.000000,50.000000,-6.150000
J3,150.000000,50.000000,5.000000
J3,50.000000,50.000000,5.000000
M3,50.000000,50.000000,-6.150000
M3,150.000000,50.000000,-9.225000
M3,50.000000,50.000000,-12.300000
M3,150.000000,50.000000,-12.300000
J3,150.000000,50.000000,5.000000
C7
'New Path
'Toolpath Name = Profile 2
'Tool Name   = 1/4"  Down-cut (57-910)
&TOOL=3
C9
TR, 12000
C6
MS,75.9,50.6
'New Path
'Toolpath Name = Profile 2
'Tool Name   = 1/4"  Down-cut (57-910)
TR, 12000
MS,75.9,50.6
JZ,20.000000
J3,50.000000,80.000000,5.000000
M3,50.000000,80.000000,0.000000
M3,50.000000,180.000000,-3.000000
M3,50.000000,80.000000,-6.000000
M3,50.000000,180.000000,-6.000000
J3,50.000000,180.000000,5.000000
C7
'New Path
'Toolpath Name = Profile 3
'Tool Name   = 1/4" Up-cut (13729)
&TOOL=4
C9
TR, 14000
C6
MS,75.9,25.3
'New Path
'Toolpath Name = Profile 3
'Tool Name   = 1/4" Up-cut (13729)
TR, 14000
MS,75.9,25.3
JZ,20.000000
J3,50.000000,80.000000,5.000000
M3,50.000000,80.000000,-6.000000
M3,50.000000,180.000000,-7.575000
M3,50.000000,80.000000,-9.150000
M3,50.000000,180.000000,-9.150000
J3,50.000000,180.000000,5.000000
J3,50.000000,80.000000,5.000000
M3,50.000000,80.000000,-9.150000
M3,50.000000,180.000000,-10.725000
M3,50.000000,80.000000,-12.300000
M3,50.000000,180.000000,-12.300000
J3,50.000000,180.000000,5.000000
JZ,20.000000
J2,0.000000,0.000000
'
'Turning router OFF
C7
END
'
'
UNIT_ERROR:
CN, 91                            'Run file explaining unit error
END